PLG0E392MD01【PDF 1/2 页】CAP ALUM 3900UF 2.5V 20% RADIAL

收藏本站

您好，
买卖IC网欢迎您。
请登录
免费注册

买卖IC网

Sheet目录873

[1页]2页

CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS

Radial Lead Type, Higher Capacitance

series

Higher Capacitance, Low ESR, High ripple current.

Load life of 2000 hours at 105 ° C.

Radial lead type :

Lead free flow soldering condition correspondence

Compliant to the RoHS directive (2011/65/EU).

Higher

Capacitance

Specifications

Item

Category Temperature Range

Rated Voltage Range

– 55 to +105 ° C

2.5 to 16V

Performance Characteristics

Rated Capacitance Range 330 to 3900μF

Capacitance Tolerance

± 20% at 120Hz, 20 ° C

Tangent of loss angle (tan δ ) Less than or equal to the specified value at 120Hz, 20 ° C

ESR (

Less than or equal to the specified value at 100kHz, 20 ° C

Leakage Current (

Less than or equal to the specified value.

After 2 minutes' application of rated voltage at 20 ° C

Temperature Characteristics

(Max.Impedance Ratio)

Z+105 ° C / Z+20 ° C

Z – 55 ° C / Z+20 ° C

1.25

(100kHz)

Endurance

Damp Heat

(Steady State)

Resistance to

Soldering Heat

Marking

The specifications listed at right shall be met when the

capacitors are restored to 20 ° C after the rated voltage is

applied for 2000 hours at 105 ° C.

The specifications listed at right shall be met when the

capacitors are restored to 20 ° C after the rated voltage is

applied for 1000 hours at 60 ° C, 90% RH.

After soldering the capacitor under the soldering conditions prescribed

here as preheat at 150 to 200 ° C for 60 to 180 seconds and peak

temperature at 265 ° C for 10 seconds or less, the capacitor shall meet

the specifications listed at right, provided that its temperature profile is

measured at both of terminal ends facing the soldering side.

Navy blue print on the case top

Capacitance change

tan δ

ESR ( 1)

Leakage current ( 2)

Capacitance change

tan δ

ESR ( 1)

Leakage current ( 2)

Capacitance change

tan δ

ESR ( 1)

Leakage current ( 2)

Within ± 20% of the initial capacitance value ( 3)

150% or less than the initial specified value

Less than or equal to the initial specified value

Within ± 20% of the initial capacitance value ( 3)

150% or less than the initial specified value

Less than or equal to the initial specified value

Within ± 10% of the initial capacitance value ( 3)

130% or less than the initial specified value

Less than or equal to the initial specified value

1 ESR should be measured at both of the terminal ends closest to the capacitor body.

2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120

minutes at 105 ° C.

3 Initial value : The value before test of examination of resistance to soldering.

Dimensions

Type numbering system (Example : 4V 1200μF)

Capacitance

Resin coated Case

9 10 11 12

Voltage(g:4V)

P L G 0 G 1 2 2 M C O 1

Size code

Configuration

φ d

Capacitance tolerance ( ± 20%)

Series

Lot. No.

L+0.5MAX.

15MIN

4MIN

Rated capacitance (1200 μ F)

Rated voltage (4V)

Size

φ D

φ 8 × 9L

8.0

(mm)

φ 8 × 12L φ 10 × 13L

8.0 10.0

Voltage

Series name

Type

φ d

8.5

3.5

0.6

11.5

3.5

0.6

12.5

5.0

0.6

Code

2.5

6.3

Please refer to page 20 about the end seal configuration.

Dimension table in next page.

CAT.8100C

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

采购需求

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

我的联系方式